KONFIGURASI REDISTRIBUTE RIPv2 dan OSPF ( cisco )

KONFIGURASI REDISTRIBUTE RIPv2 dan OSPF ( cisco )

01.32
Konfigurasi Redistribute RIPv2 dan OSPF

TOPOLOGI



 
Redistribution route merupakan proses menggabungkan dua atau lebih routing protocol untuk disatukan kedalam sebuah topologi atau network yang sama. Redistribution route biasanya digunakan apabila terjadi sebuah perubahan network, migrasi network, atau penggabungan network. 



Dalam melakukan redistribution route terdapat beberapa hal yang harus diingat untuk melakukan konfigurasi, yaitu :

  • Routing protocol menerima redistribution route sebagai external route.
  • Route hanya bisa diredistribute dengan router yang menjalankan 2 buah routing protocol.
  • Sangat memungkinkan untuk meredistribute 2 buah proses atau AS yang berbeda.
  • Static dan connected route bisa juga dilakukan redistribute.
  • Hanya rute yang terdapat pada routing table yang akan di redistribute.
  • Ketika melakukan redistribute, harus memastikan metric yang kompatible. Karena setiap routing protocol memiliki metric yang berbeda-beda, RIP menggunakan hop count, OSPF menggunakan cost, dan EIGRP menggunakan K-Values
Konfigurasi ip  address pada setiap router

ROUTER 0
Router>en
Router#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int fa0/1
Router(config-if)#ip add 10.10.10.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
\
^
% Invalid input detected at '^' marker.
Router(config-if)#ex
Router(config)#int fa1/0
Router(config-if)#ip add 13.13.13.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

Router(config-if)#ex

router 1 

 Router>en
Router#conf te
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 10.10.10.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int fa0/1
Router(config-if)#ip add 11.11.11.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#ex

router 2 

Router>en
Router#conf te
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 12.12.12.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int fa0/1
Router(config-if)#ip add 13.13.13.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ex

router 3

Router>en
Router#conf te
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 11.11.11.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ex
Router(config)#int fa1/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ex
Router(config)#int fa0/1
Router(config-if)#ip add 12.12.12.2 255.255.255.0
Router(config-if)#no sh

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up

Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

Router(config-if)#ex


KONFIGURASI ROUTING PROTOKOL PADA MASING-MASING ROUTER

ROUTER 0
Router(config)#rou
Router(config)#router os
Router(config)#router ospf 10
Router(config-router)#ne
Router(config-router)#net
Router(config-router)#network 192.168.1.0 0.0.0.255 area 0
Router(config-router)#network 10.10.10.0 0.0.0.255 area 0
Router(config-router)#network 13.13.13.0 0.0.0.255 area 0
Router(config-router)#do wr
Building configuration...
[OK]

ROUTER 1
Router>en
Router#conf te
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#rou
Router(config)#router ri
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#ne
Router(config-router)#network 11.11.11.0
Router(config-router)#ex
Router(config)#rou
Router(config)#router os
Router(config)#router ospf 10
Router(config-router)#ne
Router(config-router)#net
Router(config-router)#network 10.10.10.0 0.0.0.255 area 0
Router(config-router)#do wr

ROUTER 2 
Router>en
Router#conf te
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#rou
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#net
Router(config-router)#network 12.12.12.0
Router(config-router)#ex
Router(config)#rout
Router(config)#router ospf 10
Router(config-router)#ne
Router(config-router)#net
Router(config-router)#network 13.13.13.0 0.0.0.255 area 0
Router(config-router)#ex
 Router(config-router)#do wr
Building configuration...
[OK]

ROUTER 3 
  Router(config)#rou
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#net
Router(config-router)#network 192.168.2.0
Router(config-router)#network 12.12.12.0
Router(config-router)#network 11.11.11.0
Router(config-router)#no au
Router(config-router)#no auto-summary
Router(config-router)#ex
Router(config)#

KONFIGURASI REDISTRIBUTE PADA ROUTER 1 DAN ROUTER 2 

ROUTER 1
Router(config)#rou
Router(config)#router rip
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#red
Router(config-router)#redistribute os
Router(config-router)#redistribute ospf 10 me
Router(config-router)#redistribute ospf 10 metric 5
Router(config-router)#ex
Router(config)#rou
Router(config)#router os
Router(config)#router ospf 10
Router(config-router)#red
Router(config-router)#redistribute ri
Router(config-router)#redistribute rip sb
Router(config-router)#redistribute rip sub
Router(config-router)#redistribute rip subnets
Router(config-router)#ex
Router(config)#do wr
Building configuration...
[OK]
Router(config)#
.
ROUTER 2
 Router(config)#rou
Router(config)#router os
Router(config)#router ospf 10
Router(config-router)#
Router(config-router)#red
Router(config-router)#redistribute
Router(config-router)#redistribute ri
Router(config-router)#redistribute rip aub
Router(config-router)#redistribute rip sub
Router(config-router)#redistribute rip subnets
Router(config-router)#ex
Router(config)#rout
Router(config)#router ri
Router(config)#router rip
Router(config-router)#ver
Router(config-router)#version 2
Router(config-router)#red
Router(config-router)#redistribute os
Router(config-router)#redistribute ospf 10 met
Router(config-router)#redistribute ospf 10 metric 5
Router(config-router)#ex
Router(config)#do wr
Building configuration...
[OK]

HASIL

About

This is dummy text. It is not meant to be read. Accordingly, it is difficult to figure out when to end it. But then, this is dummy text. It is not meant to be read. Period.

Next
« Prev Post
Previous
Next Post »
Langganan: Posting Komentar (Atom)